Three-stage sequence
Taper, plug/intermediate and bottoming taps support staged internal thread formation in a prepared hole.
01 / 01
Three-piece HSS hand tap set
13 original product views are available to review.
HSS hand tap set manufacturer · Ludhiana, India
HSS Hand Tap Set
3 Pieces
Three stages. One practical set for hand threading.
SWAGIN HSS hand tap sets combine taper, plug/intermediate and bottoming taps for suitable manual internal threading operations. Share your thread size, material, quantity and drawing reference for a standard, bulk, export or custom enquiry.
3 piecesSet contentsM2 · M35 · M42Material grades62–64 HRCListed hardness
Product overview
A complete sequence for controlled internal threading.
A three-piece hand tap set provides taper, plug/intermediate and bottoming options for suitable manual threading work in prepared holes. The correct sequence depends on the hole type, thread depth, material, alignment and component requirement.
Product-family information is a starting point. Confirm size-specific dimensions, grade, tolerance, availability and commercial terms in the quotation.
Built around the application
Three tools.
One clear route.
Review the set against the thread standard, workpiece material, hole type, depth and production quantity. No universal suitability or tool-life result is guaranteed.
HSS grade options
Discuss M2, M35 or M42 according to the workpiece material and application.
Ground-thread finish
Supports controlled thread formation and dimensional review for the selected configuration.
Thread-family choice
Metric, British, unified and pipe-thread requirements can be reviewed against the exact specification.
Lead options
Select 6-thread taper, 4-thread plug/intermediate or 2-thread bottoming geometry where suitable.
Bulk and custom review
Share size-wise quantities, drawings, dimensions and commercial requirements for quotation.
Technical information
Confirm the right set configuration.
These product-family details guide the enquiry. Confirm the selected size, grade, tolerance, reference and availability in your quotation.
ProductHSS Hand Tap Set - 3 Pieces
Set contentsTaper tap, plug / intermediate tap and bottoming tap
BrandSWAGIN
ManufacturerSwastik Grand Industries
Material gradesM2 (HSS), M35 (HSS-E), M42 (HSS-ECO)
Hardness62-64 HRC
Listed size range6 mm to 100 mm
FinishGround thread
Standards listedIS 6175 Part 2: 1992, IS 6175 Part 4: 1991 and BS 949 Part 2: 1979
Thread forms60 degrees and 55 degrees
Tolerance options6H, 6G, 7H, Z-3, Z-4 or required gauge
FlutesStraight flutes; 4-flute or 6-flute options
Lead / chamfer2-thread, 4-thread or 6-thread lead
Country of originIndia
Thread families
Find the thread
you need.
These are enquiry options, not live inventory claims. Send the exact drawing where the thread designation or standard is ambiguous.
MetricCoarse pitch · Fine pitch
BritishBSW · BSF · BA · BSCY · BSB
UnifiedUNC · UNF
Pipe and fittingBSP · BSPT · NPT · NPS · NPSF · NGT · NPTF · NPSI · NPSM
Practical thread reference
Know the thread.
Specify it clearly.
For HSS taps and dies, metric pitch is measured in millimetres; inch threads are usually specified in TPI (threads per inch).
| Thread name | Full name / meaning | Example size |
|---|---|---|
| M – Metric Coarse | ISO metric coarse thread | M10 × 1.5 mm |
| Metric Fine / MF | ISO metric fine thread; normally marked M with pitch | M10 × 1.0 mm |
| UNC | Unified National Coarse | 1/2″–13 UNC |
| UNF | Unified National Fine | 1/2″–20 UNF |
| UNEF | Unified National Extra Fine | 1/2″–28 UNEF |
| UN | Unified constant-pitch series, such as 8-UN, 12-UN and 16-UN | 1-1/2″–8 UN |
| UNS | Unified National Special | 1/2″–24 UNS |
| UNR | Unified thread with a rounded external root | Specify size, TPI and series |
| UNJ / UNJC / UNJF / UNJS | Unified J-profile threads, including coarse, fine and special series | Specify complete drawing designation |
| BSW | British Standard Whitworth, coarse | 1/2″–12 BSW |
| BSF | British Standard Fine | 1/2″–16 BSF |
| BSPP / G | British Standard Pipe Parallel | G 1/2 |
| BSPT / R | British Standard Pipe Taper; R denotes external taper | R 1/2 |
| Rc / Rp | BSP mating internal threads: Rc taper, Rp parallel | Rc 1/2 or Rp 1/2 |
| NPT | National Pipe Taper | 1/2″–14 NPT |
| NPTF | Dryseal National Pipe Taper | 1/2″–14 NPTF |
| NPSM / NPSL / NPSC | American straight pipe-thread series for different applications | Specify exact series |
| BA | British Association thread | 0 BA, 2 BA, 4 BA |
| BSB | British Standard Brass thread | Diameter × TPI BSB |
| BSC / CEI | British Standard Cycle / Cycle Engineers’ Institute | Diameter × TPI BSC |
| ACME | Inch trapezoidal thread, 29° profile | Diameter × TPI ACME |
| Stub ACME | Shallower ACME thread | Diameter × TPI Stub ACME |
| Tr | Metric trapezoidal thread, 30° profile | Tr20 × 4 |
| Buttress | Asymmetric thread for heavy axial loads | Specify standard and profile |
| Rd | Round thread | Specify standard, diameter and pitch |
How to read an order size
- M10 × 1.5: 10 mm nominal diameter, 1.5 mm pitch.
- 1/2″–13 UNC: 1/2 inch nominal diameter, 13 TPI, UNC thread.
- Pitch in mm = 25.4 ÷ TPI.
- RH / LH: right-hand / left-hand thread.
- Pipe sizes are nominal: a 1/2″ BSP or NPT thread does not have a 12.7 mm outside diameter.
Unified thread families are covered by ASME B1.1. This practical industry list includes common metric, Unified, British and pipe series; it is not every specialist thread standard worldwide.
For quotationsWrite diameter + pitch/TPI + thread standard + RH/LH + tolerance class, where applicable.Individual HSS Hand Taps Discuss your thread requirement
Set contents
Start clean.
Finish close.
Use each lead according to the entry, thread depth and hole condition. The corresponding configuration is confirmed in the quotation.
Taper tap
6-thread leadLonger entry lead for progressively starting the thread.
Plug / intermediate
4-thread leadIntermediate lead for continuing a tapping operation.
Bottoming tap
2-thread leadShorter lead for finishing nearer the bottom of a prepared blind hole.
Application examples
Your component.
Your industry.
Discuss the drawing, material, machine, hole and production quantity with the manufacturer. These examples do not claim customer or project approval.
01
Nuts and fasteners
Internal threads in nuts and internally threaded components. Review a dedicated nut or machine tap for volume production.
Herusutimbul / CC BY-SA 4.0Discuss this application
02
Tool rooms, dies and moulds
Jigs, fixtures, die plates and tooling accessories where hardness, access and blind-hole clearance are suitable.
Discuss this application
03
Bicycle and cycle parts
Selected brackets and assemblies. Confirm special pitches, handedness and the exact component drawing.
Russ from Grosse Pointe Park / CC BY 2.0Discuss this application
04
Automotive and auto parts
Brackets, housings, fixtures and repair components. Distinguish manual work from repeated machine production.
Discuss this application
05
General engineering
Machine components, assemblies and workshop fixtures matched to the material and thread depth.
Discuss this application
06
Pumps, valves and fittings
Mounting holes and threaded ports where parallel, taper and sealing requirements are confirmed.
Saud / CC BY-SA 4.0Discuss this applicationHSS hand tap set enquiry
Tell us what you need.
We will review the route.
Share your thread, material, quantity or drawing reference. The enquiry is sent to the configured company inbox.
Buyer questions
Clear answers
before you order.
What is included in the HSS hand tap set?
Each set includes a taper tap, plug or intermediate tap and bottoming tap.
What details are needed for a quote?
Share thread size and pitch, quantity, material, tolerance, hole type, depth and any special requirement.
Which material grades are listed?
The source product page lists M2, M35 and M42 options. Confirm the selected grade for the application.
Can the set be used for volume nut production?
Not automatically. A dedicated nut tap or machine tap may be more suitable for repeated production.
Do you accept bulk and export enquiries?
Yes. Include size-wise quantities, destination, documents and delivery requirements.
What are the price, MOQ and lead time?
These are confirmed in a current quotation for the selected configuration.
Can you review custom sizes or lengths?
Yes. Submit a drawing or clear specification for feasibility and quotation.
Continue exploring
Related tools
for the job.
Review the individual hand tap route or return to all product families when the application needs a different tooling approach.
Individual HSS Hand Taps
View all products